People have been swapping Tiburon brakes or better (japakos) Anyone need brakes....? but you will need brackets made to hold the calipers. I myself have swapped the rear drums to Tibby brakes LC rear brake caliper brackets and I will be doing the fronts this spring.
__________________
Bete 2 engine and transmission (CA Smog legal)
used to have OBX 4-2-1 headers and intake
2 1/4 inch exhaust with a resonator
Rear disc brakes from RD Tiburon
TMW short shifter
APEXi front strut bar
Front and rear GK Tiburon seats
Astrel lip kit
Modified upper and lower grill
Roof spoiler
Painted headlights to match my car
Altezza lights (to be painted)
hello , i have complete rear axle from 2004 tiburom , one problem is i need the right bearing for the disk holder to use the same rims 4X100
or i need another rims with 5 x114,3 ,than i can took this axle into my accent ,
but at the front i need than the right brake holder ,caliper and disk
hello ihave insatalled the brakes from xg-30 at the front and rear i got bigger brake zylinder , i'll hope thats ok , at the moment i can't drive with the car to
tell jou if the brake is good or bad and if the abs -system works .
How did the XG-300 front brakes fit on your Accent? I would like to know, thanks.
__________________
Bete 2 engine and transmission (CA Smog legal)
used to have OBX 4-2-1 headers and intake
2 1/4 inch exhaust with a resonator
Rear disc brakes from RD Tiburon
TMW short shifter
APEXi front strut bar
Front and rear GK Tiburon seats
Astrel lip kit
Modified upper and lower grill
Roof spoiler
Painted headlights to match my car
Altezza lights (to be painted)
How did the XG-300 front brakes fit on your Accent? I would like to know, thanks.
Simple. Either you swap to tibby 4x114.3 front hubs or you redrill XG300 or 91-92 Galant VR4 disks to 4x100. I run them on my accent search DIY BBK and you should find what I did. I still run the stock M/C
__________________
LC '01 Accent GSI Silver - Cosmo SRI, 4x114.3 Hub Conversion, KYB GR2, Eibach Pro-Kit, Shark Racing Stress Bar and DIY BBK - more to come
LC '00 Accent GS Black - 4x114.3 Hub Conversion, Kspec Stress Bar
C52A '91 Mirage Cyborg White - 4G64DOHC N/A Lots of Mods www.heckatomb.com - My Gallery/Blog
hello ihave insatalled the brakes from xg-30 at the front and rear i got bigger brake zylinder , i'll hope thats ok , at the moment i can't drive with the car to
tell jou if the brake is good or bad and if the abs -system works .
ride on
I have a similar set up going on the front of my Accent, XG two piston calipers and disks with Elantra knuckles. I was was wondering if it was necessary to change the master cylinder or if the stock Accent one would handle the extra fluid volume of the calipers?
Simple. Either you swap to tibby 4x114.3 front hubs or you redrill XG300 or 91-92 Galant VR4 disks to 4x100. I run them on my accent search DIY BBK and you should find what I did. I still run the stock M/C
with this gay ass forum settings we can't search for those terms because they aren't long enough words.
AutoForums.com is the premier network of enthusiast-owned
enthusiast-operated automotive communities.
We operate more than 100 automotive forums where our users consult peers for shopping information and advice, and share
experiences and opinions as a community.
brakes beta swap
Linear Mode
