Hyundai Forum: Hyundai Performance Forum banner
1 - 7 of 7 Posts

·
Registered
Joined
·
111 Posts
Discussion Starter · #1 ·
Does anyone know of any websites that tells you how to get the front blinker corners off of a 2001 tiburon. If not, then if you know how, can you please explain, I tried to get them off myself, I could only see one screw that looked like it was holding it in, but when i took it off, I still couldn't get the corner off. Please help!!!!<img src=/images/forums/snitz/cry.gif width=16 height=16 border=0><img src=/images/forums/snitz/mad.gif width=16 height=16 border=0>


<hr noshade width=60% size=1 align=left>A girl can only get you so far; but a car can get you the quarter mile.

2001 Silver Hyundai Tiburon
Package 5
sunroof
power everything
leather
STICK SHIFT
[email protected]
Mods: 2 Logic PSW12 a Logic LSL-2680 amp
 

·
Registered
Joined
·
181 Posts
Use your screw driver as a lever, and push it out forwards. There is a plug that it will pop out of. Once you get them out once, it's easy to get them out any time after.


<hr width=60% noshade size=1 align=left>Black 2000 Tib SE
SR Altezzas and clear corners
Custom red grills
Momo shiftknob
Sony CDX-M650 Deck
Formula 1 Tint
MBRP rear section exhaust (not installed yet... see title)
Patiently waiting for Kore ver III CAI...
 

·
Registered
Joined
·
218 Posts
There may be alittle easier way if u don't wanna ruin ur paint and shyt. Get under hte car and undo two screws from the plastic wheel thingy and just look for the corner light under there and just push it out. Thats how I did it and they came out fairly easy. But a pain in the a§§<img src=/images/forums/snitz/finger.gif width=33 height=15 border=0>


<hr width=60% noshade size=1 align=left>'01 Cardinal Red Tibby
HDK Clear Corners
APC Altezzas
APC Hyper White Turn Signals
Naxos Hyper White low/high beams
Alpine CD Head Unit, Pyle 600W Amp, 2 Rockford 10" Subs
<img src="http://www.yabb.info/avatars/download.php?923.gif">
 

·
Registered
Joined
·
85 Posts
I just put clear corners (thanks SR!) on my '98 last week and there is a piece that clips to the headlamp housing. I stuck a bent clothes hanger down there to push the clip down while I was pulling on the corner. If you are not careful, you will break the little plastic clip if you just yank on it. Take alook at you new corner, notice that black square looking clip... That is what you are looking for. I don't think you will hurt anything if you break that clip, but the rubber seal won't be as tight around the corner. <img src=/images/forums/snitz/thumbup.gif width=25 height=18 border=0>


<hr width=60% noshade size=1 align=left>WIL!
'98 White FX
 

·
Registered
Joined
·
657 Posts
wait wait wait....

before you pop it out with a screw driver... just place a shop rag between the car and your screwdriver, then ram it in and lever it out...

don't scratch you're pretty paint :)


<hr width=60% noshade size=1 align=left>2001 Targa Top Tiburon w/Full Roll Cage
 
1 - 7 of 7 Posts
This is an older thread, you may not receive a response, and could be reviving an old thread. Please consider creating a new thread.
Top