Hyundai Forum: Hyundai Performance Forum banner

1 - 1 of 1 Posts

·
Registered
Joined
·
6 Posts
Discussion Starter #1
I Want to purchase The tri-phase module from www.nextlevelracing.com they said that there device connects into the MAF sensor, my Hyundai coupe( tiburon 2.0l 4 cylinder) has a MAP/IAT sensor, is it still possible to connect this device to my engine.they asked if my hyundai dealer would know the correct wireto connect there device to, but thats not a question i could ask them(warranty!!!)

What is the other sensor on the plenum chamber on the right had side of the MAP/AIT sensor just past the throttle body.

I have attached e-mails between myself and next level racing(below)

Damien,

That is quite different than the American Spec model, although many other cars
are like that here. Is Hyundai able to point out the correct wire or do they
not have that information?

----- Original Message -----
From: damien oreilly
Sent: 11/2/2005 2:55:52 PM
To: [email protected]
Subject: Re: Hyundai MAF sensor?

Brad



The sensor on my car is located on the front of the plenum chamber(centre
of) past the throttle body,
It is the MAP sensor (manifold absolute pressure sensor) it is also the IAT
sensor (intake air tempature sensor)

There are four wires going into the wiring harness/sensor

Can the tri-phase still be used on my car, if yes, can you explain to me how
> to install it.
>
I included some information about MAP sensors


(The manifold absolute pressure (MAP) sensor is used to determine the
absolute pressure (not the relative to atmospheric pressure) of the air
inside the intake manifold and the atmosphere (barometric pressure). This
information is used to determine the density of the air entering the
combustion chamber, which is used when calculating the proper air/fuel
mixture for the engine.)

I am very grateful for your help

Regards

> Damien

From: "Next Level Performance" <[email protected]>
To: "damien oreilly" <[email protected]>
Subject: Re: Re: Re:hyundai Part two of previous e-mail
Date: Tue, 1 Nov 2005 17:08:52 -0500

Damien,

Your MAF sensor could be located further upstream from the intake tube. It
would probably be easiest to just call or stop by your local Hyundai dealer
and ask them to point it out to you.

Best Regards,

Brad M.W.
NLP

Original Message -----
From: damien oreilly
Sent: 11/1/2005 3:39:58 PM
To: [email protected]
Subject: Re: Re:hyundai Part two of previous e-mail

Brad

My 02 Model is the same as the U.S. 2003. It is the new model? Hope you
can
still help me.Will the tri-phase work on this model. taking into account
that there is no wiring harness anywhere on the air intake.
Please reply a.s.a.p

Regards

Damien

From: "Next Level Performance" <[email protected]>
To: "damien oreilly" <[email protected]>
Subject: Re: Re:hyundai
Date: Tue, 1 Nov 2005 13:01:02 -0500

Certainly Damien,

Your ecm/maf wiring harness is located right on your intake tube,
> >behind
your airbox. It is a 5 wire harness
Regards,

Brad M.W.
NLP

> > > >----- Original Message -----
> > > >From: damien oreilly
> > > >Sent: 11/1/2005 3:51:20 AM
> > > >To: [email protected]
> > > >Subject: Re:hyundai
> > > >
Hi Brad
Can you tell me the location of the ecm/maf sensor on the hyundai tiburon or directions how to install the tri-phase correctly.

Damien



Certainly Damien,

The Tri-Phase is currently available and in stock for your Hyundai,
> >and it will definitely install to your car. Installation is quite simply,
to your
ecm/maf wiring harness. Once plugged in, all you have to do is ground the
module (anywhere you choose) and mount the control switches
(anywhereyouchoose). The entire installation process should only take you 20 - 30
minutes. If you have any other questions, please don't hesitate to
let
us
know
Regards,

Brad M.W.
NLP

[Edited by damienoreilly on Nov 3, 2005 7:32 AM]
 
1 - 1 of 1 Posts
Top