[Accento]

Is it dificult to install a tach on the Accents and does it work.

 

[CHADHATESU]

First things first.
What year is you're Accent?

To somewhat answer you're question though.

"does it work?" Yes


"Is it dificult to install a tach on the Accents?" No, not really. There's only four wires.(12v ingnition, 12v dash light, a ground, and the RPM signal) The one you need to know about is the RPM signal wire from the ECM. On '95-'99 Accent's I know it is the number six wire on the main harness, it's a solid white wire. On cars with the factory tach in the dash you can just tap into the back of you're guage cluster. I'm not sure if the '00-'01 models are the same.

Later,
Chad <img src=icon_smile_evil.gif border=0 align=middle>

 

[Red_AGT]

Welcome to the board Accento.

Some people have done this mod and like Chad said, I'm guessing that it does work. Shouldn't be too hard.

Are you planning to add a tach externally or are you trying to get it in the gauge cluster?

Chad... if you look under the names, there listed is some information and Accento seems to be driving a 1998 Accent. <img src=icon_smile.gif border=0 align=middle>

----------------------

[=1997 Red Accent GT=]

 

[Accento]

Thanx for the information <img src=icon_smile_big.gif border=0 align=middle>

 

[EnricoPalazzo]

<BLOCKQUOTE id=quote><font size=1 face="Verdana, Arial, Helvetica" id=quote>quote:<hr height=1 noshade id=quote>On '95-'99 Accent's I know it is the number six wire on the main harness, it's a solid white wire. <hr height=1 noshade id=quote></BLOCKQUOTE id=quote></font id=quote><font face="Verdana, Arial, Helvetica" size=2 id=quote>

Umm, unless Australia has different coloured wires which is highlt unlikely, the wire which is to be tapped into is the green wire with a slim white strip down the middle.

 

[Haste]

I have installed a cluster with tacho into my 99 excel/accent.

All my installation instructions and wiring etc are on my website.

http://www.geocities.com/hyundaixl2000

then click on the D-I-Y button

http://www.geocities.com/hyundaixl2000

 

[Red_AGT]

Hey... I just read this on the http://www.hyundaituner.com/index2.html site. Hope it helps.

<BLOCKQUOTE id=quote><font size=1 face="Verdana, Arial, Helvetica" id=quote>quote:<hr height=1 noshade id=quote>

shaun
2. Re:Aftermarket Tach.

I have a 97 accent wo the tach. I added a autometer tach to my accent with the help of chad, and here is how to do it.
Your tach wire will connect to the "all white" wire coming off of your ECM which is located underneath your dashboard on the far left on the drivers side. You may set off a airbag light when doing this, I did on mine, so just a warning. After you hook that up, if you look under your steering wheel there is a wire harness coming off the ignition switch, you will need to splice into the black and white wire which is only HOT when the ignition is turned on. For illumination I have been trying to get it hooked up to the dimmer but I didden't do that yet. Post back here if you have a different year accent, and I will help the best I can.
-shaun
Date: 02:46 p.m. on 07-07-2001

<hr height=1 noshade id=quote></BLOCKQUOTE id=quote></font id=quote><font face="Verdana, Arial, Helvetica" size=2 id=quote>

----------------------

[=1997 Red Accent GT=]

 

[Red_AGT]

Check this page out... might be helpful.

http://www.hyundaituner.com/cgi-hyundaituner/Ultraboard/UltraBoard.cgi?action=Read&BID=13&TID=1831&SID=

----------------------

[=1997 Red Accent GT=]