Hyundai Forum: Hyundai Performance Forum banner

1 - 6 of 6 Posts

·
Registered
Joined
·
6,177 Posts
Discussion Starter #1
Yes I am looking for some advice on where to put a toggle switch for some fog lights, I just don't know where to mount it at to make it look good and look like part of the interior, I am gettin a BLUE toggle also, THANKS<img src="http://www.plauder-smilies.de/sad/nixweiss.gif" border=0><img src="http://www.plauder-smilies.de/errrr.gif" border=0><img src="http://www.plauder-smilies.de/sad/conf.gif" border=0> And something that wont ruin the HYUNDAI warranty<img src="http://www.plauder-smilies.de/deal.gif" border=0>



<hr noshade width=60% size=1 align=left>Jason Mann

Missouri/Kansas Rep.
Team-SR
 

·
Registered
Joined
·
541 Posts
you can get the regular toggle for the tiburon from the dealer i'm sure...it on the left side where those plastic pieces are on the dash...

Mateus


<hr width=60% noshade size=1 align=left>"Even in death we live!"
 

·
Registered
Joined
·
324 Posts
You can get a switch from the dealer. It'll cost you about $25. Let me tell that I think that the fog lights are already pre-wired. Behind the dash where the switch is supposed to be, it already have a harness. I think you just have to wire it to the fuse box under the hood. I may be wrong<img src=/images/forums/snitz/disapprove.gif width=15 height=15 border=0>


<hr width=60% noshade size=1 align=left>'01 Cardinal Red Tiburon
17" Nakayama Shumacher Racing Wheels
AOS CAI, Magnecor Wires
Zex Hyperformance Plugs
Sony Xplode system
MTX Subwoofers
Shark Racing Strut bars
Cat-back exhaust
 

·
Registered
Joined
·
6,177 Posts
Discussion Starter #4
Hey thanks but i don't want to rip the dash out of the Tib. it is COLD outside so I was going to run the wire to a toggle in the cab but I need a good place for a clean look. The foglights are the glo-lights from APC that I am looking at.


<hr width=60% noshade size=1 align=left>Jason Mann

Missouri/Kansas Rep.
Team-SR
 

·
Registered
Joined
·
16 Posts
I always like the idea of taking out the coin holder (useless anyway) and put in a master arm switch for some NOS. You could easily put the switch there and all you have to take off is the shifter boot.

<img src=/images/forums/snitz/approve.gif width=15 height=15 border=0><img src=/images/forums/snitz/mad.gif width=16 height=16 border=0>


<hr width=60% noshade size=1 align=left>THE IRISH SHARK
TeamSR-083
Regional Coordinator-Rocky Mounatin Chapter
Collins Engineering
http://www.fxtreme.org/members/Zeek/index.html
 

·
Registered
Joined
·
6,177 Posts
Discussion Starter #6
Yeah I was thinking of some like plexi glass piece molded to the spot and fitted with a toggle ie:
<img src="http://www.jcwhitney.com/images/imagecache/I3475.gif" border=0> but in blue and the measurements I will have to check the coin holder on the switch is Fits into 1-1/8" x 7/16"


<hr width=60% noshade size=1 align=left>Jason Mann

Missouri/Kansas Rep.
Team-SR
 
1 - 6 of 6 Posts
Top